The surface of the label material determines which thermal transfer ribbons produces the best adhesion. Open the front cover. Removing rewound backing paper. A dial [20A] displays the value. To achieve a Gold competency level, Solvusoft goes through extensive independent analysis that looks for, amongst other qualities, a high level of software expertise, a successful customer service track record, and top-tier customer value. P Continued overleaf ALX 92x with half used up label roll. Avery Dennison Hardware Type:
|Date Added:||12 March 2006|
|File Size:||57.26 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Solvusoft: Microsoft Gold Certified Company
The material and the ribbon take longer to cool. P For information on choosing a suitable thermal transfer ribbon, refer to section Selecting the printing material on page 4.
This website is using cookies. Guide the ribbon end under the ribbon deflection [15B] and thread through to the side of the printhead [15A].
To achieve a Gold competency level, Solvusoft goes through extensive independent analysis that looks for, amongst other qualities, a high level of software expertise, a successful customer service track record, and top-tier customer value.
Put an empty take-up roll on the upper left ribbon mandrel.
Turn the dispensing edge [24A] to the desired position. You are downloading trial software. Name 1 Adjustment knob for printhead 13 pressure Feed roller 2 Ribbon rewinding mandrel 14 Deflection roll 3 Ribbon unwinding mandrel 15 Material guide 4 Operation panel 16 Opener 5 Deflection roll 17 Brake roller 6 Material dancer arm 18 Adjustment wheel for denison sensor 7 Material unwinder 19 Print roller 8 Guiding rod 20 Dispensing edge 9 Backing paper rewinder 21 Printhead 10 Backing paper dancer arm 22 Ribbon deflection axle 11 Pressure roller 23 Ribbon deflection roller with stress relief 12 Lever for pressure roller 24 Ribbon roller [Tab.
Position the spring-suspended block [10A] in a way that the contact roll presses in the middle on the backing paper. Assuming spent ribbon has gathered on the rewinding mandrel: Remove the roll of used ribbon from the rewinding mandrel.
Removing spent backing paper The backing paper rewinder can exactly rewind the amount of backing paper remaining from a material roll with mm diameter [2A].
This can led to poor printing results. How is the Gold Competency Level Attained? A  Measuring the punch position A. A  Assuming backing paper denmison gathered on the rewinder: Loosen the two thumb screws [10B] at the spring-suspended blocks.
Thread the backing paper around dancer arm [12A] and deflection roller as illustrated . The tensioning mechanism of the rewinder is slackened. B  Adjusting the material guide B. Pull the ribbon under the printhead from the side, then, unwinding some ribbon, smoothen it out .
Tighten the thumb screw again.
Printer Drivers European | Avery Dennison
To ensure in those cases, that the label start is correctly identified, a punch offset can be preset. The printout is produced by applying precise bursts of heat to the material under the printhead. B A  Inserting the label material at the print module. To do this loosen the thumb screw [5A] at the front material guide, shift the material guide [5B] crossways to the feed direction and tighten thumb screw again.
As a result, the print quality may degrade — particularly at high print speeds. ax
Avery Dennison ALX 924 Setup Manual User Manual
Pull the empty ribbon core off the unwinding mandrel and put it on the rewinding mandrel. If an overly wide ribbon is used, creasing may occur in the ribbon. Caps [19B] protect the nuts against being adjusted by accident. Peel labels off the backing paper for a stretch of appr. Size of the ribbon roll: Pay attention to the following factors when selecting label material: Tighten the backing paper backwards and close the lever .